|
|
Product View |
Description |
| |
|
SPLITTERS |
|
|
|
GHN-SP-UPLC
Universal Power Line
Communications
Splitter
|
The Model GHN-SP-UPLC Universal Power
Line
Communications Splitter device is used to provide a controlled AC port to
the PLC modem, separate and isolate the high-frequency PLC signal from AC
power, and make it accessible on three BNC ports labeled L1, L2 and L3 with
a controlled impedance. Having the PLC signal on BNC ports allows using
standard instruments and accessories to perform measurements and build
controlled topologies. Capable of performing Dynamic PSD Test and Cognitive
Frequency Exclusion test (Dynamic Notching) per EN 50561-1 using Model 501
and 501-Probe-Coax.
|
GHN-SP-UPLC Specifications
|
|
Electrical Safety
|
Complies with EN 61010-1 : EN 60950-1
|
|
Insertion Loss (Single Line)
|
EUT to BNC OUT (L1-L3): 0.35dB@ 80 MHz, 0.45dB@ 100 MHz
|
|
Differential Line Impedance
|
100 ohm +/- 10% (1MHz to 100 MHz)
|
|
Continuous Operating Voltage
|
90 to 240VAC, 50 Hz/60 Hz
|
|
Outputs: L1, L2, L3
|
BNC-female Connector, 50 Ω
Impedance, 1MHz to 100MHz
|
Specifications
are subject to change without notice. Made in USA.
Order with
Approved Schuko Power Adaptors
|
|
GHN-SP-SPLCOMB-UPLC-3
3-Channel Splitter/Combiner
|
The Model GHN-SP-SPLCOMB-UPLC-3
3-Channel Splitter/Combiner is a symmetrical power splitter and combiner where
all the ports have 6 dB attenuation to each other.
This product provides one
set of three BNC ports on one side and two sets on either side. The spacing
between connectors is the same as in the GHN-SP-UPLC Universal Power Line
Communications Splitter, allowing the device to be connected directly using
male-male BNC barrels to reduce the number of cables. (Unused ports of the
3-Channel Power Splitter/Combiner must be terminated with 50Ω.)
The GHN-SP-UPLC connected to the GHN-SP-SPLCOMB-UPLC-3
|
|
|
GHN-AT-PROG-UPLC-3
3-Channel-Slope
Programmable Attenuator
|
The Model GHN-AT-PROG-UPLC-3-Slope 3-Channel Programmable
Attenuator is used along with the GHN-SP-UPLC in the PSD Measurement test set
up. Offers an attenuation range of 1 to 127 dB in 1-dB increments.
|
GHN-AT-PROG-UPLC-3-Slope
Specifications
|
|
Number of Channels
|
3
|
|
Attenuation Range
|
1 to 100 dB in 1-dB increments
|
|
Frequency Response Uniform
|
± 0.5 dB from 1 MHz to 127 MHz
|
|
Impedance
|
50 ohm
|
|
Connectors
|
SMA Connector Jack, Female Socket 50
Ohm
|
|
Interface
|
USB
|
Specifications
are subject to change without notice. Made in USA.
|
|
|
|
|
APPROVED SCHUKO POWER ADAPTORS |
|
|
|
GHN-ADP-CH_BR
|
The GHN-ADP-CH_BR is a Schuko power adaptor
for Switzerland
and Brazil. It is approved for use with the
Model GHN-SP-UPLC Universal Power
Line
Communications Splitter. |
|
|
GHN-ADP-IT_RCH
|
The GHN-ADP-IT_RCH is a Schuko power adaptor for
Italy and Chili. It
is approved for use with the
Model GHN-SP-UPLC Universal Power
Line
Communications Splitter. |
|
|
GHN-ADP-AU_RCN_AR
|
The
GHN-ADP-AU_RCN_AR
is a Schuko power adaptor for
Australia, China and Argentina. It is approved for
use with the
Model GHN-SP-UPLC Universal Power
Line
Communications Splitter. |
|
|
GHN-ADP-NA
|
The GHN-ADP-NA is a Schuko power adaptor for North
America. It is
approved for use with the
Model GHN-SP-UPLC Universal Power
Line
Communications Splitter. |
|
|
GHN-ADP-UK
|
The GHN-ADP-UK is a Schuko power adaptor for
the United Kingdom. It is
approved for use with the
MModel GHN-SP-UPLC Universal Power
Line
Communications Splitter. |
|
|
1XBNCM-1XSMAM-1F |
BNC(male)-to-SMA(male) cable, length 1 foot |
|
|
BNC-BNC-BARRELPLUG |
BNC Plug-to-BNC Plug in-line barrel connector |
|
|
BNC-TERM-50 |
50-ohm BNC Terminator |
|
|
1XRJ45M-1XRJ45M-3F |
Cat6 Shielded Patch Cable - SSTP Bare Copper, RJ-45 male connectors,
length 3 feet |
